Test
Very strong and rugged clear polycarbonate box to store standard pin mounts with 3.2mm (1/8"). This box is watertight, crushproof and dustproof. The strong hinges, locking clasps and soft silicone O-ring seal makes this an ideal transport, shipping and storage box for SEM samples on pin mounts. The holder insert is numbered 1-18 and accommodates all types of pin mounts form 6.4 to 50mm diameter.
Machined from solid steel and brass/nickel plated. Incorporates a stainless steel mesh top and bottom to allow for fluid exchange. Comes with two sections; each section holds 12 specimens in 12 cavities cavity measures 4.5mm(D) x 6mm(H)..
For the storage of 15 capsule blocks in numbered cavities.
Lanthanum hexaboride (LaB6) and cerium hexaboride (CeB6) cathodes are ideal for many small spot size applications such as SEM, TEM, surface analysis and metrology, and for high current applications such as microwave tubes, lithography, electron-beam welders, X-ray sources and free electron lasers. Greater brightness from low work function yielding higher currents at lower temps than tungsten. Cambridge MVM base.
Type: CEBIX (CeB6)
Angle: 90°
Tips: 20 mm
Type: non-shunted
The QX-102 Capsules are used for scanning electron microscope imaging of wet materials and biological samples, including liquid foods, cosmetics, oils, and paints, particles in solutions, adherent and non-adherent human and animal cells, and microorganisms. The samples can be visualized either directly or by following appropriate contrast enhancement staining or labeling procedures. The capsule serves as a cell culture dish, specifically designed for the SEM . No coating or embedding of the sample are required, enabling electron microscopy imaging with easy sample preparation comparable to light microscopy. Includes QX-202 Capsules and all the accessories.
This mount is made from a special certified Aluminum alloy which does not contain any of the objectionable elements that may interfere with samples collected for GSR . These mounts are 12.7 mm x 11 mm.
Hitachi cylinder mount has a M4 tapered hole with female thread. Made from lathe finished ultra-pure aluminum. M4 tapered hole.
Head: 1"
Height: 6 mm
Hitachi M4 Thread SEM mounts made from lathe finished ultra-pure aluminum.
Head: 2"
Height: 1/4"
Scanning electron microscope specimen mount with 45 degree angle. Made from lathe finished ultra-pure aluminum.
Head: 5/8"
Height: 3/8"
This multi pin stub adapter for JEOL is designed to save time. It is made from vacuum aluminum with stainless steel set screws. It accommodates up to four standard 12.7 mm (1/2") pin stubs with 3.2 mm (1/8") pin.
Type: JEOL
Cylinder specimen mounts are for use with JEOL scanning electron microscopes. The mounts are made from ultra-pure aluminum with a standard lathe finish.
Head: 1-1/4"
Height: 3/8"
9 divisions surface min stub mounts are for use with FEI/Philips, ZEISS/LEO, Cambridge, Leica, Amray, Tescan and Camscan SEMs. Mounts are made from lathe finished ultra-pure aluminum.
Head: 1"
Pin height: 9 mm
Pin diameter: 3.2 mm
This mount which is made from aluminum is used for the mounting and tilting of samples from 0 – 90 degrees as well as for SEM investigation with small working distances. The mount is marked for 30, 45, 70 and 90 degress. The table measures 11 x 11 mm (0.46" x0.46")and the overall size is 14 x 14 x12.7 mm
Type: 3.2 mm x 8mm Pin
This 25.4 mm in diameter 45 Degree multi pin holder is designed to save time. It allows for a higher SE signal without having to tilt the specimen It is made from machined aluminum with stainless steel Allen set screws. It accommodates up to three standard 12.7 mm (1/2") pin stubs with 3.2 mm (1/8") pin.
Mini SEM pin stub mount for Cambridge, Leica, ZEISS/LEO, FEI/Philips, CamScan, Tescan, ETEC and Amray. Made from lathe finished ultra-pure aluminum.
Head: 6.6 x 1.3 mm
Pin height: 3/8"