Test
Red bakelite with wood filler, thermosetting. Routine examination of soft to medium hard materials. Suitable as backing.
Observing the ultrastructure of cells under an electron microscope is an important aspect of biological research, especially in the neurosciences. These embedding crystals were designed to simplify the preparation of samples and make the process more time efficient.
D.E.R. 736 pract. Shorter chain than D.E.R. 732, lower viscosity, gives less flexible blocks. Epoxy equivalent weight 175 - 205; viscosity 0.03 - 0.06 Pas at 25 C.Used in electron microscopy. Size - 100ML Storage Conditions - +15 C TO +30 C
Same as the Kwik Gard but in its original container. A two-part silicone elastomer, ideal for potting and encapsulating applications. Very low dielectric constant sealing compound used in patch clamping and many other lab applications. After cure, will withstand -55 degree to 200 degree C. Curing time for this silicone 24hrs@25 degree C, and 15 min.@150 degree C.
An aqueous-based frozen section embedding medium designed to support tissue blocks in cryostat sectioning. Formulated to promote rapid freezing, enhanced sectioning and consistent results at a working temperature of -20 degree C.
Light yellow melamine with mineral and glass filler, thermosetting. For soft to medium hard materials. Excellent edge retention.
The Kwik-Gard is specially packaged Sylgard184 silicone that offers a quicker and easier way to apply the silicone, eliminating the messy procedure of preparing the mixture before application. Its special cartridge controls the precise mixing ratio to ensure proper curing. The disposable tip mixes resin and hardener as they are dispensed. Since no air is introduced during mixing, the resin does not need degassing for most applications. The mixed silicone is applied directly to the site, reducing preparation time and material waste.
Each Kwik-Gard cartridge contains 37 mL of resin and hardener. The dispensing tip has a dead volume of 0.75 mL. Curing time for this silicone is 24hrs@25 degree C, 15 min.@150 degree C. 2 cartridges of resin/hardener, 10 tips.
D.E.R.(TM) 332 used as embedding medium | Mol Wt: 340.41 | 1675-54-3 | MFCD00080480 | 250G
The Kwik-Gard is specially packaged Sylgard184 silicone that offers a quicker and easier way to apply the silicone, eliminating the messy procedure of preparing the mixture before application. Its special cartridge controls the precise mixing ratio to ensure proper curing. The disposable tip mixes resin and hardener as they are dispensed. Since no air is introduced during mixing, the resin does not need degassing for most applications. The mixed silicone is applied directly to the site, reducing preparation time and material waste.
Each Kwik-Gard cartridge contains 37 mL of resin and hardener. The dispensing tip has a dead volume of 0.75 mL. Curing time for this silicone is 24hrs@25 degree C, 15 min.@150 degree C.
Black bakelite with carbon filler, thermosetting. SEM examination.
The Kwik-Gard is specially packaged Sylgard184 silicone that offers a quicker and easier way to apply the silicone, eliminating the messy procedure of preparing the mixture before application. Its special cartridge controls the precise mixing ratio to ensure proper curing. The disposable tip mixes resin and hardener as they are dispensed. Since no air is introduced during mixing, the resin does not need degassing for most applications. The mixed silicone is applied directly to the site, reducing preparation time and material waste.
Each Kwik-Gard cartridge contains 37 mL of resin and hardener. The dispensing tip has a dead volume of 0.75 mL. Curing time for this silicone is 24hrs@25 degree C, 15 min.@150 degree C. Dispenser, 1 Cartridge of resin/hardener, 5 tips.
This formulation is especially well suited for Mohs cryostat sectioning. It freezes at optimum cutting temperatures of -10 deg C and below. No residue is left on slides during the staining procedure, thereby eliminating undesirable background staining.
Black bakelite with wood filler, thermosetting. Routine examination of soft to medium hard materials. Suitable as backing.
Black epoxy with mineral filler, thermosetting. For hard materials. Excellent edge retention.
The Kwik-Gard is specially packaged Sylgard184 silicone that offers a quicker and easier way to apply the silicone, eliminating the messy procedure of preparing the mixture before application. Its special cartridge controls the precise mixing ratio to ensure proper curing. The disposable tip mixes resin and hardener as they are dispensed. Since no air is introduced during mixing, the resin does not need degassing for most applications. The mixed silicone is applied directly to the site, reducing preparation time and material waste.
Each Kwik-Gard cartridge contains 37 mL of resin and hardener. The dispensing tip has a dead volume of 0.75 mL. Curing time for this silicone is 24hrs@25 degree C, 15 min.@150 degree C. Tip has dead volume of 0.75 mL.