Test
Very strong and rugged clear polycarbonate box to store standard pin mounts with 3.2mm (1/8"). This box is watertight, crushproof and dustproof. The strong hinges, locking clasps and soft silicone O-ring seal makes this an ideal transport, shipping and storage box for SEM samples on pin mounts. The holder insert is numbered 1-18 and accommodates all types of pin mounts form 6.4 to 50mm diameter.
For the storage of 15 capsule blocks in numbered cavities.
Machined from solid steel and brass/nickel plated. Incorporates a stainless steel mesh top and bottom to allow for fluid exchange. Comes with two sections; each section holds 12 specimens in 12 cavities cavity measures 4.5mm(D) x 6mm(H)..
The fixation clips 6 mm in diameter provide support spring for small and thin specimens during mounting.
Circlips are for all EMS TEM sample holders and specimen rods. They are made from heat treated Beryllium copper. The Circlip extraction tool is for removing our Circlips from all TEM sample holders.
Cambridge, Phillips, Camscan, B&L, Etec, Zeiss SEM specimen mounts. Tapered end pin, slotted head.
Head: 1/2"
Pin height: 6 mm
Pin diameter: 1/8"
An Innovative Enclosed Specimen Holder for Liquid TEM. K-kits are sample holders designed to facilitate convenient TEM observation of liquid samples, allowing nanoobjects, aggregates, and agglomerates (NOAAs) in liquid samples to be characterized. With vacuum compatible sealing of liquids in electron-transmitting thickness, K-kits are micro reaction chambers for countless experiments in materials, chemical, and biological research.
Gap: 0.2 µm
Lanthanum hexaboride (LaB6) and cerium hexaboride (CeB6) cathodes are ideal for many small spot size applications such as SEM, TEM, surface analysis and metrology, and for high current applications such as microwave tubes, lithography, electron-beam welders, X-ray sources and free electron lasers. Greater brightness from low work function yielding higher currents at lower temps than tungsten. Cambridge MVM base.
Type: CEBIX (CeB6)
Angle: 90°
Tips: 20 mm
Type: non-shunted
Hitachi cylinder mount has a M4 tapered hole with female thread. Made from lathe finished ultra-pure aluminum. M4 tapered hole.
Head: 1"
Height: 6 mm
Hitachi M4 Thread SEM mounts made from lathe finished ultra-pure aluminum.
Head: 2"
Height: 1/4"
Scanning electron microscope specimen mount with 45 degree angle. Made from lathe finished ultra-pure aluminum.
Head: 5/8"
Height: 3/8"
This multi pin stub adapter for JEOL is designed to save time. It is made from vacuum aluminum with stainless steel set screws. It accommodates up to four standard 12.7 mm (1/2") pin stubs with 3.2 mm (1/8") pin.
Type: JEOL
Dual imperial/metric scales calibration slide. 50 mm in 0.1 mm divisions and 2" in 0.005" divisions. In wooden case. Ideal for calibrating optical products with a large field of view, such as stereo microscopes or imaging systems. Negative pattern formed in low reflective chrome for incident light applications. 76 mm x 25 mm.
SPM calibration specimens are produced by holographic fabrication that assures high accuracy and precision. The standards provide easier testing of your SPM, improved accuracy of critical dimension measurements and accuracy of 0.5% (1 std. dev.). The pattern height of greater than 100nm provides excellent image contrast. There is uniform coverage of entire chip which allows for imaging anywhere on the chip. Array of Posts. Pitch 297. Al bumps on Si. Use contact or TappingMode.
Mount: SEM Pin
This 117 mm in diameter multi pin holder is designed to save time It is made from machined aluminum with 302 stainless steel springs that hold the pin stubs in place. It accommodates up to forty nine standard 12.7 mm (1/2") pin stubs.